Chain Joinery – Fixing stiff links

I’m still working on getting everything working smoothly with my old ’93 Specialized Rockhopper, after replacing the chain, cassette, front cranks and sprockets.  To compensate for larger chainrings, I ended up having to add a couple of links to my chain, and I thought I’d pass on a tip.

I have always found it frustrating trying to put chains back together with a chain tool.  I would always start by pushing the rivet all the way back into the link, and almost invariably, the link would end up so stiff I could barely move it.  I could never figure out how to get it loosened up properly.  My chain tool includes a secondary “ramp” for fixing stiff links, but it never seemed to do me any good.  It would spread the link apart a little bit, but the link would remain stiff.  Working the chain back and forth laterally, as recommended on various web sites, didn’t work for me either.  It was very frustrating, until I came up with the following strategy:

  1. Begin reassembling the chain with the chain tool as you normally would, except instead of pushing the rivet all the way into the link, tighten the chain tool only about 1 full turn or so, just so the rivet goes in far enough to hold the link together.
  2. Remove the chain from the tool, and verify that the link moves freely.
  3. Put the chain back in the tool (regular position, not “stiff link” position) and tighten another ¼ to ½ turn.
  4. Repeat steps 2 and 3, pushing the rivet in just a tiny bit each time, and testing the link, until you feel the link start to stiffen up.
  5. Put the chain into the “stiff link” position on the chain tool.  Usually, this is the position closest to the crank handle.  Tighten handle around ¼ turn, just enough to slightly spread the link.  Never turn the handle more than ¼ turn in this position, or you may distort the link.
  6. Remove tool from chain.  Check to make sure the link has loosened up.
  7. Continue to push the rivet into the link little by little, checking the link for tightness each time (steps 2-3), and loosening it up as needed (steps 5-6), until the rivet is all the way in the link.  That should do it!

I’ve had great success with this method.  The trick is to keep the link loose by making small, gradual adjustments, rather than trying to free the link up after the rivet has been inserted all the way.  Good luck and happy riding.

Ironic Flat

It’s been a sloppy start to May.  Almost every day has been cloudy with off-and-on drizzle.  Plus it’s been warm and muggy.  Not exactly ideal biking weather, but it hasn’t kept me out of the saddle yet.

Yesterday I was all set to ride my mountain bike to work, when I discovered the rear tire was flat as a pancake.  Lacking time to change it, I moved all my gear over to my road bike and took it instead.  This morning, I wanted to take the mountain bike, because it has fenders and the roads were wet, so I took a look at the tire.  This tire has a plastic liner in it that is designed to guard against flats.  This liner is a “Slime” brand.  “Mr. Tuffy” is another popular brand.  Well, it appears that the edge on the end of the liner was rubbing against the tube, and it was just sharp enough to eventually cause a puncture.  The liner had been in for around 2 months.  The tire itself was not punctured, and there was nothing else inside the tire that could have caused the flat.  So ironically enough, it appears that the liner, which is in there for the sole purpose of preventing flats, ended up causing a flat.

I took a pair of scissors and rounded off the end of the liner a bit, to get rid of the “point.”  Then I put a new tube in and put the tire back on.  We’ll see if that does the trick.  If it doesn’t, the next step will be to try taping down the end of the liner, and if that doesn’t take care of it, I’ll try a different brand of liner.

The fun never ends!

Two Fish Bikeblocks

I’m finishing up October with 14 rides, tying with July and April.  In keeping with this somewhat off-year of riding, it’s fewer rides in October than I had in 2008, 2009 or 2010.  I’m at 130 rides on the year.  My goal for the year is 150, which should be doable.

A couple weeks ago, I picked up a couple of Two Fish BikeBlocks.  These are rubber blocks with velcro straps, meant for securing a frame pump to your frame.  The Bikeblocks do a decent job.  They’re a bit pricey at around $7 each, and unless your pump is  6″ long or shorter, you’re going to need two of them.  They do a good job of keeping the pump in one place; my commute has some bumpy stretches, and I didn’t have any problem with the pump sliding or moving around.  The blocks stand the pump off around 1″ away from the frame, which could be problematic with certain frames.  On my single speed, the most logical place to mount the pump would be on the underside of the top tube; however, while it did fit, the rear brake cable rubbed against the Bikeblocks, which would have worn them down over time.  My next try was the seat tube, where I have a water bottle cage, so I had to mount the pump so it stuck out to the side.  This put it too close to my legs, to where I kept brushing against it.  The lower part of the downtube was a no-go too; the pump didn’t clear the crank arm.  I ended up putting the pump on the side of the downtube, above the bottle cage.  I had to tilt it slightly towards the front to keep my knee from brushing it during standing climbs; and in this position, there’s only about ½” clearance between the pump and the pedal, and the top of the pump is ½” or so from the front fender.  It’s a tight squeeze, but it fits, and it gets the pump out of my side pannier, which was my goal.  I’ll ride with it like this for awhile and see how it works out long-term.

Beep. Beep. Beep.

So.  We were without air conditioning in our building for awhile today.  Fortunately it’s a nice day out with unseasonably low humidity and a breeze, so I was able to open the window to make it tolerable.

It’s amazing how much beeping you hear in populated regions (like college campuses) nowadays.  Seems like all day long, there’s beeping somewhere from a truck backing up.  There’s so much of it that it just kind of fades into the background with other stuff like birds chirping.  After awhile you don’t even hear it.  Something about the sound makes it carry over really long distances, and it’s also very non directional, making it hard to tell where it’s coming from.  It could be right around the corner, or it could be a mile away.  You can’t tell.  It’s just sort of “there.”

Last fall I put fenders on my road bike, which I use daily for commuting.  They work great, but they make the bike really noisy.  Now that summer is here and the weather is drier, I decided to try to figure out why the fenders are so noisy.  I took the front fender off and rode to work with just the rear fender.  The bike was TONS quieter without the front fender.  I think that’s the culprit.  The fender itself doesn’t rattle, so apparently something is vibrating against the bike frame.  My front fork doesn’t have dropouts to mount fenders, so I had to use zip ties to attach the struts.  Could be the struts vibrating against the fork, or the front of the fender vibrating against the underside of the brake, or who knows what else.  If I can’t figure it out and make it stop, I may end up getting a clip-on fender to use on the front.  Or I could replace my front fork, or I could forget about fenders on the road bike and get a hybrid or cyclocross bike (with better clearance for fenders) to use in wet weather.  One can certainly never have too many bikes…

Back on the bike after ice storm

I rode my bike to work today for the first time since the ice storm that hit the Baltimore/Washington area this past Tuesday and Wednesday.  My usual commute takes me through Elkridge, Relay, and Arbutus, MD, including a short trip through the Patapsco State Park Avalon Area.  Today, the roads were fine for the most part, actually a little drier and less salt-strewn than I expected.  The park, however, was still a massive sheet of ice, and being that I was on a road bike with skinny non-ice-friendly tires, I skipped the park and did a short detour onto U.S. 1 instead.  Biking on U.S. 1 is never my first choice, but it was only 1/4 mile on a stretch that has adequate shoulders.  All the same, it was the first time I had ever biked this stretch, and fortunately it wasn’t too bad (aided, I’m sure, by the fact that it was 9:30am and traffic was thinning out).  Nice to know that I have this option available in the future on days when the park is impassable.

The roads weren’t too bad on the UMBC campus (my destination) either, other than maybe a little more salt than the county roads.  The sidewalks were passable.  On the roads they use what appears to be the same salt the county uses, but for the sidewalks they use this weird white foamy-pellety stuff that sticks to shoes and tires, and gets tracked all over the place inside the buildings.  Thanks to full fenders, my bike stayed pretty clean for the entire ride, until the very end when I rode on the sidewalk.  Now the tires are covered with this crap, and I’m sure there’s a long trail of it leading from the front door to my office suite.  (Update — apparently this is Calcium Chloride, and come to think of it, it looks suspiciously similar to the Calcium Chloride “Hardness Plus” pellets I put in my swimming pool.  Wonder if it’s cheaper per pound…)

The ride home should be interesting.  It’s sunny right now, but apparently it’s supposed to cloud up through the afternoon and there’s a chance of snow showers.  We’ll see how it goes.

Fenders on a Road Bike, Part 2

This is part 2 of my story about how I put fenders on my road bike.  Read about my motivation for doing this in the first installment.

There are a couple types of fenders made for road bikes.   “Full” fenders cover the back wheel all the way down to the bottom bracket, and the front wheel from below the cranks to just past the front brake.  There are also “clip-on” quick-release fenders made specifically for road bikes.  An example of these is the SKS “Race Blade.”  These work, but they are smaller and provide less wheel coverage than full fenders. I knew that full fenders would be a bigger job to mount on my bike, but I figured if I absolutely could not get them to fit, I could always fall back on the clip-ons.  With that in mind, I went shopping for a set of full fenders.  The two biggest names in inexpensive road bike fenders seem to be SKS and Planet Bike. I read up on both, and eventually decided to go with a set of Planet Bike “Cascadia” fenders, which I ordered from Niagra Cycle Works.  The fenders arrived after a few days and I went to work putting them on.

Full fenders typically attach to the bike in two places.  The top of the fender attaches to the front fork or rear brake bridge, and the back of the fender is supported by struts that attach to threaded holes in the bike frame near the hubs.  The rear fender is usually also attached to the “seat stay bridge,” a short horizontal piece between the bottom bracket and the rear wheel.  On a road bike with caliper brakes, the fender goes between the brake caliper and the tire, and typically shares the same mounting hole with the brake.  So, to accommodate fenders, the bike needs:

  • Adequate vertical clearance underneath the front fork and between the brake calipers and the tire
  • Threaded holes on the front fork and rear seat/chainstays, near the hubs
  • Some way to attach the tops of the fenders to the front fork / rear brake bridge (possibly sharing the brake mounting hole)
  • A seat stay bridge piece to attach the front end of the rear fender

My bike met some of the criteria.  All of the clearances were adequate, and it had a seat stay bridge and the necessary mounting holes for the rear fender (although I was currently using them for my rack).  The problems:  It had no mounting holes on the front fork, and no easy way to attach the tops of the fenders to the brake mounts.  So I would need to work around these limitations somehow.

I began by mounting the rear fender.  I unbolted my rack and attached the fender struts underneath the rack supports.  Conveniently, the rack’s mounting bolt was long enough to accommodate both the fender struts and the rack supports, so I bolted them both to the same hole.  The front of the fender attached easily to the chain stay bridge using a zip tie.  For the top, Planet Bike uses a snap-on plastic clip.  The clip has a bolt slot that’s intended to mount behind the rear brake, but as mentioned above, there’s nowhere there I can bolt it; the rear brake is attached with a recessed hex nut that does not have threads to accept a fender bolt.  However, I was able to use zip ties to attach the mounting clip to the seat stays (this is covered in Planet Bike’s instructions), so problem solved there.  This mounting method does slightly reduce the fender’s clearance underneath the brake, though, so it may not be usable on a bike with extremely limited clearance.  Once the fender was mounted, I adjusted the struts until it didn’t rub the tire, and I was done.  That was pretty easy.

The front fender was more of a challenge.  My fork doesn’t have holes to mount the struts, so I had to improvise.  A couple of web sites recommended using metal or nylon p-clamps, but I can’t use these on my fork because its arms are not round enough.  Instead, I opted to just zip-tie the struts to the fork.  This is not an ideal solution, but it works well enough.  the quick-release skewer caps keep the ties from slipping off the fork, and the ties seem to stay in place otherwise.  But I’d still like to come up with something more elegant.  On to the top.  The front fender has a permanently-attached metal bracket instead of a plastic clip.  The front brake uses the same type of recessed nut as the rear brake, so there’s nowhere to attach the bracket behind the fork.  But unlike the rear, there’s nowhere on the fork to zip-tie the bracket either.  So my only option was to remove the front brake and mount the bracket between the brake and the fork (actually behind the lock nut that retains the brake spring — otherwise the bracket didn’t clear the steering tube).  I did this, and wasn’t happy with the results.  It made it impossible to adjust the fender’s position without also affecting the brake, and it also made it impossible to easily remove the fender.  I needed a better solution, so I went web surfing again, and found out about Problem Solvers Sheldon Fender Nuts.

Sheldon Fender Nuts replace the recessed nuts that hold the brake calipers in place.  The difference is, the Sheldon nuts are slightly longer, so they protrude outside the brake mounting hole, and they have a thread to accept a fender mounting bolt.  The front fender can then mount behind the fork as intended, and the fenders can be adjusted independently of the brakes.  The nuts come in sets of 2 (one for back and one for front).  I ordered a set from Jenson USA.  The front nut was an extremely tight fit in my fork.  Initially, I had to tap it with a hammer to seat it enough to mate with the threads on the brake, but eventually it “broke in” enough that I could thread it on and off the brake without too much trouble.  I was worried I’d torque it apart or otherwise destroy it, but it turned out to be pretty sturdy.  The mounting bolts that came with the Cascadia fenders did not fit the thread on the Sheldon nut — I had to scrounge up some matching bolts and washers from my parts drawer.  After that, though, the fender went on easily and was a snap to adjust.  So far I’ve only used the Sheldon nut on the front fender.  Eventually I’ll take the zip ties off the back fender and remount it with the Sheldon nut, but the nuts were worth the price just for the front.

Initially, I couldn’t get the front wheel to stop rubbing the fender.  No amount of fiddling with the fender seemed to help.  Finally I figured out that my wheel was not properly centered in the fork.  I undid the quick release and centered the wheel, and suddenly the fender no longer rubbed.  There’s not a whole lot of side-to-side tolerance with these fenders, so buyer beware.  I’m a little worried at what might happen if I break a spoke..

After the fenders were on, I didn’t have to wait long to test them out.  I took the bike out shortly after a storm, and the fenders worked like a champ.  I hit my first puddle and watched all the water squirt out the front of the fender, instead of up on the bike, my clothes, etc.  In normal riding conditions, I don’t really notice the fenders except for maybe a rattle here or there when I hit a bump.  The fenders don’t get in my way at all.  The instructions warn that my foot might touch the front fender during slow turns, but I haven’t had that problem.  All in all, even if the installation was a bit of a pain, the fenders were well worth it and I highly recommend them for all-weather commuting.

Fenders on a Road Bike, Part 1

I’ve been an occasional bike commuter for a little over three years.  My commuter bike is a 2001 Giant OCR-1, a road bike with an aluminum frame and a carbon fork.  Back in the big 1980s, I spent my teen years delivering newspapers, and went through a seemingly-endless string of cheap 10-speed beater bikes.  I rode the bikes year-round in all kinds of weather conditions.  Every one of them had fenders – the big, heavy, metal kind that start to rust after a couple days in the elements.  The fenders may not have been stylish, but they did their job, keeping mud and grime off the bike and its rider.  Of course, back then I didn’t appreciate them.

Flash forward to the 1990s.  At some point, bike manufacturers stopped putting fenders on bikes.  I bought a mountain bike in 1994 – no fenders.  Ditto for my road bike, bought in 2002.  Nowadays, most bikes in the U.S. are sold for recreation.  Road bikes, in particular, now seem to be mostly geared towards racing and weekend club rides.  And indeed, when I bought my bikes in the 90s and 00s, I first used them for recreation.  I took the mountain bike out on trails, and used the road bike for weekend club rides.  I only rode the bikes in good weather, so I never missed the fenders from my old bikes.  Somewhere along the way, I forgot about the more utilitarian uses for bikes – commuting, errand-running, etc.  I had a college degree and a desk job, and no longer needed a bike for work, or so I thought.

Flash forward another few years.  With young kids, I no longer had as much time for leisure riding.  I wasn’t in quite the shape I was a few years before.  I wanted to find a way to do some more riding, so I decided to try riding my bike to work.  Gas prices were high at the time, so I figured I could save some money on gas and improve my fitness at the same time.  My ride to work is only about 8 miles, which is long enough to get a decent workout, yet short enough that it doesn’t take too long (with small children and a busy family life, time is at a premium).  I tried commuting by bike a few times and discovered that I enjoyed it, so I kept it up for 3 years.  At first I rode only in the summer, and then only when it was sunny and dry out.  It wasn’t until 2008 that I took the plunge into all-season bike commuting, and it wasn’t until then that I missed fenders.  Summers here on the east coast tend to be pretty dry, with occasional thunderstorms providing most of the precipitation.  That all changes in the Fall, when we have lots of damp, misty, drizzly weather.  After my first couple of wet rides, my fender-less bike (and most of its cargo) was completely covered in mud and other junk that splashed up from the road.  Not only was this bad for the bike (bottom brackets don’t like road grit), I had to spend an hour or so after each ride hosing the bike down, wiping off the grime, and re-lubing everything.  It was a major hassle, and I quickly reached the conclusion that cold-season commuting wasn’t going to happen regularly if I couldn’t come up with a better alternative.  That’s when I remembered fenders.  If I could somehow retrofit fenders onto my bike, they should solve most of my problems.

My next post will describe the process I went through to research, choose, and mount a set of fenders on my road bike.  It was a tricky and occasionally frustrating exercise, but the end result was well worth the effort.